IEC1107 Electricity meter interface

Equipment, circuits, projects, procedures

Postby technojunkie » Sun Oct 21, 2007 12:00 am

Hi

Has anybody built the IEC 1107 Electricity Meter Interface which was featured way back in march 2002?

I've got the hardware working OK, but the PC software is giving me problems.
It gets to the part " ...Waiting for identification message..." and just sits there doing nothing.

I'm going to assume that the software is meant to send out some sort of command at different Baud rates until it gets a reply from the meter. Is this correct? I've had a datalogger between the serial port of my PC and the interface circuit, and there is no transmitted data at all. I know the serial port and interface are OK because I used other PC software with the IR LED and IR detector aligned for a simple loop-back test and everything works fine.

Has anybody got one working ?
Does anybody know more about the IEC 1107 protocol?

Best regards and thanks for reading my first post.
technojunkie
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Postby tingo » Sat Oct 27, 2007 12:00 am

Technojunkie
Does anybody know more about the IEC 1107 protocol?

The IEC 1107 protocol is now called IEC 61107[1].
Hope this helps.

1) IEC61107
--
Torfinn'
tingo
 
Posts: 5
Joined: Thu Jan 02, 2014 10:40 am

Postby yogesh-india » Wed Apr 07, 2010 12:00 am

hi, Good moring.......
i need your help regading to 1107.
i m going to implement 1107 protocol with my electricity meter. will you please help me for hardware and software.
it will be great hlep for me if you provide some reffered document.

i had found some document on this same website, but i need some more to understand correctly.


thanks

yogesh
yogesh-india
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Postby ali » Mon Nov 01, 2010 12:00 am

Dear .

I know about IEC 1107 Protocol very well and i have a lot of software concern with this kindly tell me about your meter type and manufacturer of this meter so that i will send you the concern software. till then try to use attached software.

Please write me on Hassanali143@hotmail.com for further detail.

Ali
Attachments
Test1107pack.rar
(814.16 KiB) Downloaded 472 times
ali
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Postby topete » Tue Nov 09, 2010 12:00 am

Hi everyone, i´ve been trying to arm and set to work the circuit for the iec1107, but i have note made it, yet, and i´d like to ask a little of help, but first i have some doubts:

I live in Mexico, and i´m making the comunication probes with american registers, do i need a diferent circuit to get the the desired comunication?

Well, i hope anyone can help me, we'll be in touch

.....ah something else, if anybody can please answer my simple doubt, could you please do it at topete_27@hotmail.com ??

THAN´S A LOT
topete
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Postby 9fingers » Mon Jul 04, 2011 12:00 am

TechnojunkieHi

Has anybody built the IEC 1107 Electricity Meter Interface which was featured way back in march 2002?

I've got the hardware working OK, but the PC software is giving me problems.
It gets to the part " ...Waiting for identification message..." and just sits there doing nothing.

I'm going to assume that the software is meant to send out some sort of command at different Baud rates until it gets a reply from the meter. Is this correct? I've had a datalogger between the serial port of my PC and the interface circuit, and there is no transmitted data at all. I know the serial port and interface are OK because I used other PC software with the IR LED and IR detector aligned for a simple loop-back test and everything works fine.

Has anybody got one working ?
Does anybody know more about the IEC 1107 protocol?

Best regards and thanks for reading my first post.



I've just come across this posting and have exactly the same problem.
It does look like the code is supposed to put out a challenge to the meter but there is nothing being output to the IR transmitter LED.

Does anyone have an idea on how to proceed please.
I now have a Solar PV system on my roof and would like to read the meter memory to see how much power is actually going back to the grid.

Thanks

Bob
9fingers
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Postby aas » Mon Nov 14, 2011 12:00 am

Hi ALL


Try to test the software on a old windows 95 or 98 version.

A lot of software for the RS232 will not work with XP or Windows 7
aas
 
Posts: 1
Joined: Thu Jan 02, 2014 10:46 am

Re: IEC1107 Electricity meter interface

Postby giorgio » Thu May 08, 2014 7:36 pm

Does it work with Elster A100C?

Do I need to give any passwords to read data from it?

Has anyone managed to work with
http://www.rotwang.co.uk/projects/meter.html
instead?

Thanx
giorgio
 
Posts: 1
Joined: Thu May 08, 2014 7:31 pm

Re: IEC1107 Electricity meter interface

Postby Elominique » Tue Jul 15, 2014 4:14 am

This post is very useful for me,thank you all of you coque de samsung galaxy note pro 12.2 coque rigide ipad mini
User avatar
Elominique
 
Posts: 1
Joined: Tue Jul 15, 2014 3:57 am

Re: IEC1107 Electricity meter interface

Postby bakre3792 » Tue Jul 26, 2016 12:40 pm

HI,
I am working on reading data from ISKRA ME 172 via RS 485, I tried to respect the protocol 1107 but I still don't have any answer from the device.
Any help?
Thanks.
bakre3792
 
Posts: 1
Joined: Tue Jul 26, 2016 11:20 am


Return to Test & Measurement

Who is online

Users browsing this forum: No registered users and 3 guests