The Elektor Forum will close. See also this link. From Friday March 15st it is no longer possible to log in to the forum. However, the content of the forum will remain visible until the end of March. As of April 1st the forum will definitely go off the air.

Soldering Iron Tip Saver

The electronics enthusiast's product design cycle

Postby k_s_soin » Wed May 30, 2007 12:00 am

I had built this circuit in 1985 from Elektor Magazine. I am um unable to find tis mag in my collecetion. This circuit uses a counter perhaps a CD 4060, triac and two switches. I want to buld this circuit again.
Can any one help.
k_s_soin
 
Posts: 1
Joined: Thu Jan 02, 2014 10:40 am

Postby tinminer » Wed May 30, 2007 12:00 am

There is a project in the December 1984 issue" give your soldering tip a longer life" , it may be the one you want.
tinminer @ bigpond.com
tinminer
 
Posts: 12
Joined: Thu Jan 02, 2014 10:37 am

Postby tinminer » Wed May 30, 2007 12:00 am

I found that article in my old magazines, let me know if you cannot find what you need.

tinminer @ bigpond.com
tinminer
 
Posts: 12
Joined: Thu Jan 02, 2014 10:37 am

Postby karanbir » Thu Sep 24, 2009 12:00 am

Yes that is the circuit I am lookig for.
(Excuse the absence from the scene for so long, I have registered again as I lost my id and password.)
Can you send me the scan of this article.
Thanks once again for your response.
Best Regards
Karanbir
karanbir
 
Posts: 2
Joined: Thu Jan 02, 2014 10:40 am

Postby maxxypane » Fri Nov 18, 2011 12:00 am

Well, here is the list of parts that will be used to build this circuit. Hope this will help you. R1-2.2MΩ, R2-18KΩ, R3-1KΩ, R4- 1KΩ, R5-1KΩ, R6-1MΩ, VR1- 500KΩ (504), C1- 220nF (224), C2- 10nF (103), D1- LED, D2- LED, D3- 1N4001, Q1- BC547, IC1- CD4060, RL1- Relay etc.

Gold Contact Repair Kit'
maxxypane
 
Posts: 5
Joined: Thu Jan 02, 2014 10:39 am

Re:

Postby radcliffkaty1 » Mon Jul 16, 2018 12:45 pm

maxxypane wrote:Well, here is the list of parts that will be used to build this circuit. Hope this will help you. R1-2.2MΩ, R2-18KΩ, R3-1KΩ, R4- 1KΩ, R5-1KΩ, R6-1MΩ, VR1- 500KΩ (504), C1- 220nF (224), C2- 10nF (103), D1- LED, D2- LED, D3- 1N4001, Q1- BC547, IC1- CD4060, RL1- Relay etc.Gold Contact Repair Kit'


I tried to open the link you have shared "Gold Contact Replating Kit" but it is not working. But then, I found that you have a shared the link of soldertools.net website. From that site, I also purchased the same kit and to be true, that kit rocks. I would like to correct that share link so that others can also get that.

Gold Contact Replating Kit
radcliffkaty1
 
Posts: 9
Joined: Thu Jun 28, 2018 11:10 am


Return to CAD, Simulation, PCBs, Making, 3D Printing

Who is online

Users browsing this forum: No registered users and 1 guest